|
|||
author | remove search highlighting | ||
---|---|---|---|
posted: 2 Sep 2015 17:33 from: madscientist click the date to link to this post click member name to view archived images |
I know this was posted somewhere before , but can someone direct me to a drawing of the various track gauges for 00-SF. I'm going to run up some new ones and rather then cobble measurements off existing ones, I'd like to go to the horses mouth so to speak Dave |
||
posted: 2 Sep 2015 18:54 from: Martin Wynne
click the date to link to this post click member name to view archived images |
Hi Dave, Brian Tulley (polybear) is holding the current drawings. No doubt he will reply shortly. I can post the original check gauge tool drawing: 2_150847_350000001.png (the arrowed dimensions are the critical ones) With 0.92mm rail it is possible for the check gauge to go as low as 15.16mm if the rail is left loose in the slots and the gauge tool is on the limits. Experienced users will know to pack the slots with aluminium cooking foil to get a good fit in the gauge tool for maximum accuracy. Unfortunately batches of rail vary, so this is unavoidable with fixed-slot gauge tools usable on any batch of rail. If you are making your own gauge tool, you could make a spring-loaded self-adjusting design instead. The finished check gauge should not be less than 15.2mm on the track. From the drawing you should be able to derive plain 16.2mm roller track gauge tools quite easily. As far as I know, only Brian has the 3-point gauge tool drawing. The tool diameter should be as small as convenient. Ideally it should fit between adjacent timbers, allowing soldering to take place on both sides. If you are planning constructing complex formations, it is worth milling flats on each side for better access. regards, Martin. |
||
posted: 3 Sep 2015 08:45 from: madscientist click the date to link to this post click member name to view archived images |
Thanks. I have a lathe and cnc milling , so I should be able to make all the gauges including a 3 point track gauge . ( is there drawings for that ? ) | ||
posted: 3 Sep 2015 19:39 from: polybear click the date to link to this post click member name to view archived images |
Hi, It would probably be unfair of me to post the engineering drawings generated for the purposes of Gauge manufacture, since the designs are now in effect the property of C&L Finescale after I handed over the project to them (I enjoyed being able to provide them, but the value of each batch of Gauges I ordered from the machine shop was around a thousand pounds a time; as the popularity of 00-sf gradually increased I was becoming more and more concerned that a commercial source may also decide to manufacture/sell similar Gauges to 00-sf dimensions, with the risk that I may be left with a batch of Gauges and no customers. In fact another source is now also supplying 00-sf Gauges, namely DCC Concepts in Australia). However, I'm sure I can help out with some information that will help you achieve what you want. Check Rail Gauges Critical dimensions are as posted by Martin above; it's worth putting a flat on End "A" (so the cross-section view of "A" appears as a "D-shape".). This allows easy use of the Gauge in the vicinity of the Crossing Vee. 16.2mm Roller Gauge Similar to the Check Rail Gauge design, but symmetrical at both ends (i.e. End "C" has dimensions as per "End A" in Martin's drawing). Again there is a flat, but this is only required at one end of the Gauge. Finally, the critical dimension is 16.20 - 16.23mm. 3-Point Gauge These are a dead useful Gauge - I find they work really well when making plain (straight) trackwork, as they hold the rails very efficiently. See here (Post#77) : http://www.rmweb.co.uk/community/index.php?/topic/69145-attention-00-sf-track-builders/page-4 The width of the Gauge slots is 1.0mm +/-0.02mm (it being a lot easier to get a 1mm milling cutter than a 0.95mm cutter...), whilst the slot depth is 0.9 - 0.95mm (not a critical dimension); the Gauge width between the inner and outer pairs of slots is 16.20 - 16.23mm; the distance between the outer faces of the wider pair of Gauge slots is 30mm +/-0.1mm. Pictures of all Gauges are here: http://00-sf.org.uk/#gauge_tools Please bear in mind that the Gauges I supplied (now C&L) were originally designed for use with C&L Code 75 Bullhead Rail; other rail sections (and rail from other suppliers) may require different slot widths; see here (Post #134): http://www.rmweb.co.uk/community/index.php?/topic/94567-00-sf-and-00-bf-can-you-mix/page-6 HTH Brian |
||
posted: 4 Sep 2015 06:05 from: Hayfield
click the date to link to this post click member name to view archived images |
Can I make a comment that if using plastic chairs do not make the rail slots too deep, as the rail is held at a 1-20 cant and the head of the rail needs to rotate in the slot. if too deep the rail is held upright whilst in the gage, but relaxes back after thus gauge narrowing | ||
posted: 4 Sep 2015 09:19 from: polybear click the date to link to this post click member name to view archived images |
Thanks John - good point. The rail slots on the 15.2mm/16.2mm Roller Gauges previously supplied by me were nominally 1.7mm deep. I've only used them for soldered track construction though, so cannot comment as to the rail cant on glued track construction. HTH Brian |
||
posted: 7 Sep 2015 15:51 from: madscientist click the date to link to this post click member name to view archived images |
while I am disappointed that what might have been public information at one time is now commercial, I am thankful that Brian provided a few hints my own view is that such information should be clearly in the public domain, simply to ensure that such information is not lost to the users. I dont think it would have an effect on any commercial producers of gauges, one way or the other I intend to machine my own and in doing so I will draw up an Autocad dimensioned drawing, I will post that here, if no one objects. dave |
||
Last edited on 7 Sep 2015 21:13 by madscientist |
|||
posted: 7 Sep 2015 15:56 from: madscientist click the date to link to this post click member name to view archived images |
The width of the Gauge slots is 1.0mm +/-0.02mm (it being a lot easier to get a 1mm milling cutter than a 0.95mm cutter...), whilst the slot depth is 0.9 - 0.95mm (not a critical dimension); the Gauge width between the inner and outer pairs of slots is 16.20 - 16.23mm; the distance between the outer faces of the wider pair of Gauge slots is 30mm +/-0.1mm for completeness, whats the distance between the outer faces of the inner( narrower ) slots |
||
Last edited on 7 Sep 2015 15:57 by madscientist |
|||
posted: 7 Sep 2015 22:28 from: keithj15
click the date to link to this post click member name to view archived images |
Regardless what gauge I am building track in, I find spring clip gauges (as used by Norman Solomon) feel more accurate and secure than roller gauges. Roller gauges are generally cut too deep, and so come into contact with the chairs on fine scale track. In the end it all comes down to availability and personal choice. However when I wanted to get a couple of clip gauges for code 75 OO fine scale, after much searching on the web, I could not find a supplier and in the end turned to an engineering hobbyist who was able to produce what I wanted. I still make use of roller gauges, but mainly for plain track rather than turnouts and crossings. | ||
posted: 7 Sep 2015 22:50 from: Hayfield
click the date to link to this post click member name to view archived images |
What's a clip gauge please | ||
posted: 9 Sep 2015 04:40 from: Terry Flynn
click the date to link to this post click member name to view archived images |
madscientist wrote: I know this was posted somewhere before , but can someone direct me to a drawing of the various track gauges for 00-SF. I'm going to run up some new ones and rather then cobble measurements off existing ones, I'd like to go to the horses mouth so to speakThe AMRA fine tolerance standard has a fully dimensioned track gauge drawing covering many fine scale track gauges. The gauge is of the clamp variety and can be used for any size rail. The AMRA H0 fine tollerance standard = 00-SF. Cheers,Terry Flynn. |
||
posted: 9 Sep 2015 08:46 from: Martin Wynne
click the date to link to this post click member name to view archived images |
Terry Flynn wrote:The AMRA fine tolerance standard has a fully dimensioned track gauge drawing covering many fine scale track gauges. The gauge is of the clamp variety and can be used for any size rail. The AMRA H0 fine tollerance standard = 00-SF. Terry's track gauge drawing is on page 6 here: http://www.amra.asn.au/finewheeltrack.pdf It provides rail clamping for the rails at 16.25mm. The actual track gauge is not too critical provided it is not less than 16.2mm. The AMRA H0-SF dimensions are slightly different from 00-SF but not by much. However, it does not provide clamping, or even any fixed slot, for the check rails -- for the much more important 15.2mm check gauge dimension. Also the gauge is drawn symmetrical, making no allowance for gauge-widening. For the crossing flangeway, a 1.0mm shim is much easier to use during construction than a roller-type gauge. regards, Martin. |
||
posted: 9 Sep 2015 18:04 from: polybear click the date to link to this post click member name to view archived images |
Hi Dave, Whilst I did post drawings of the original roller gauges on the 00-sf forum some years ago, it was for the purposes of allowing purchasers of the first batch of gauges to comment/approve the design and /or suggest changes prior to parting with money in advance of manufacture of the first batch of gauges. When it became apparent that the demand for subsequent batches would become an on-going event I decided to remove the drawings to minimise risk of another party using them ( perhaps an established manufacturer) and making very large batches which would attract discounts of scale; this may have resulted in me being left with a batch of unsold gauges with £1K of money tied up in them. As far as I can recall the drawing for the 00-sf 3-point gauge has never been posted on-line. As previously mentioned, it would be wrong of me to post the drawings now that C&L have the rights to them. HTH Brian |
||
posted: 9 Sep 2015 18:10 from: polybear click the date to link to this post click member name to view archived images |
madscientist wrote:The width of the Gauge slots is 1.0mm +/-0.02mm (it being a lot easier to get a 1mm milling cutter than a 0.95mm cutter...), whilst the slot depth is 0.9 - 0.95mm (not a critical dimension); the Gauge width between the inner and outer pairs of slots is 16.20 - 16.23mm; the distance between the outer faces of the wider pair of Gauge slots is 30mm +/-0.1mm Hi Dave, I don't have access to the drawing at the moment, but from memory it was something like 3mm or so. If it is too wide then it could affect the curve of the rail thru' the slot; too narrow and it could prove to be too fragile and not last long. The original 3-point gauges were manufactured from steel, incidentally, and i believe still are. HTH Brian |
||
posted: 9 Sep 2015 22:37 from: madscientist click the date to link to this post click member name to view archived images |
Thanks Brian. | ||
posted: 11 Sep 2015 05:42 from: Terry Flynn
click the date to link to this post click member name to view archived images |
Martin Wynne wrote: Terry Flynn wrote:Hello Martyn,The AMRA fine tolerance standard has a fully dimensioned track gauge drawing covering many fine scale track gauges. The gauge is of the clamp variety and can be used for any size rail. The AMRA H0 fine tollerance standard = 00-SF. I have built many turnouts of various geometries using 3 AMRA gauges. The result is trackwork that does not need any adjustment for derailment free results. Similar to the shim method, there is no need to have the rail held held in a slot, as the gauges check gauge is correctly sized(>15.2mm) when the check rail is pushed against the gauge. When positioning the check rail I use 2 AMRA gauges. Having a symmetrical gauge means the user cannot use the gauge the wrong way around and is suitable for making K crossings and other track where check rails are required opposite each other. I am not saying the AMRA roller gauges are the ultimate method for construction the crossing V and K but the AMRA gauges are dimensionaly optimized to do the job for both V and K crossings. My experience is if you use a minimum radius as calculated using the AMRA minimum radius standard, gauge widening is not necessary. After saying this I make the track gauge 16.5mm at the point blades for easier construction.I would not waste time making a typical 3 point gauges because they are not accurate enough and do not provide enough gauge widening, To correctly gauge widen the 3 point track gauge needs to be as long as the longest fixed wheelbase locomotive you wish to run. Cheers, Terry Flynn. |
||
posted: 25 Aug 2016 14:25 from: madscientist click the date to link to this post click member name to view archived images |
Folks, I now find it impossible to source 00-SF 3 point track gauges , C&L seem to have so source for them Is it not time for the benefit of the gauge to release a drawing that at the very least I can either make them myself or have them made on commission |
||
posted: 25 Aug 2016 14:53 from: Martin Wynne
click the date to link to this post click member name to view archived images |
Hi Dave, It's disappointing after Brian handed over his gauge designs to C&L that they have not been able to maintain them in stock or provide the same level of service that Brian provided. They obviously sell well, or they wouldn't keep going out of stock. The web site doesn't say that the 3-point gauges are not on order from the supplier, although it is worrying that the most important gauge, the check gauge, is no longer listed. I posted the drawing for that earlier in this topic. Sorry I don't have access to any of the other drawings. C&L are now stocking the DCC Concepts 00-SF gauges, and may feel that the duplication is not justifiable. The DCC Concepts gauges are multi-slot roller gauges and therefore barely usable in my view, but that's just me. They could be cut down to 2-slot gauges by the user of course. I have noticed that C&L are now at long last stocking gauges for the DOGA-Intermediate standard, and do have them in stock. The C&L business is currently up for sale, which may be affecting the level of restocking they are prepared to undertake until a new owner is found. regards, Martin. |
||
posted: 25 Aug 2016 15:03 from: madscientist click the date to link to this post click member name to view archived images |
thanks Martin thankfully I have a set of the check gauges , C&L have a " no order " against the 3 point gauges for a long time now i really think brian should really release the drawings into the public domain to ensure that the 00-SF community can secure gauges Dave |
||
posted: 25 Aug 2016 15:13 from: Martin Wynne
click the date to link to this post click member name to view archived images |
madscientist wrote: i really think Brian should really release the drawings into the public domain to ensure that the 00-SF community can secure gaugesHi Dave, I have found that the gauge drawings are on the 00-SF Yahoo Group files at: http://groups.yahoo.com/neo/groups/00-SF/files/00-SF%20Track%20Gauges%20Folder/ They are Brian's copyright, so I won't post them here for now. regards, Martin. |
||
posted: 25 Aug 2016 15:27 from: madscientist click the date to link to this post click member name to view archived images |
Martin Wynne wrote:madscientist wrote:i really think Brian should really release the drawings into the public domain to ensure that the 00-SF community can secure gaugesHi Dave, Martin , you're a genius , I should also point out that recent ECJ rulings mean that a picture that is a link to the original source is not a copyright violation. But I think Brian should be asked to release them formally , after all they are published on the Internet , so his previous comments re C&L do not really stand up. ( dont have a way of directly emailing him as I dont have his email , maybe you could ask him ) Dave |
||
Last edited on 25 Aug 2016 15:28 by madscientist |
|||
posted: 25 Aug 2016 15:32 from: madscientist click the date to link to this post click member name to view archived images |
Ill make up some 3-points gauges in the CNC miller ( proxxon ) in delrin first to see how i get on, then in brass | ||
Last edited on 25 Aug 2016 15:33 by madscientist |
|||
posted: 25 Aug 2016 16:05 from: Martin Wynne
click the date to link to this post click member name to view archived images |
madscientist wrote:( don't have a way of directly emailing him as I don't have his email , maybe you could ask him )Hi Dave, You can contact Brian via a PM on RMweb to "polybear": http://rmweb.co.uk/community/index.php?/user/289-polybear/ But it's very likely that he will reply here soon. regards, Martin. |
||
Please read this important note about copyright: Unless stated otherwise, all the files submitted to this web site are copyright and the property of the respective contributor. You are welcome to use them for your own personal non-commercial purposes, and in your messages on this web site. If you want to publish any of this material elsewhere or use it commercially, you must first obtain the owner's permission to do so. |